What is ride control?
A vehicle in motion is affected by various factors. Some of them are the weight of the vehicle, the weight distribution, the speed of the concerned vehicle along with external factors such as the condition of the road as well as something like the wind. These are all responsible for how the vehicle moves around on a highway.
These factors might seem to be negligible when seen individually but when all of them are combined together, they seriously affect the comfort of your ride. There is one factor which is the most important of them all.
The most important factor in the quality of the ride is the suspension system which includes components such as shocks, springs, and the struts. All of the mentioned components in the suspension system must be in a good condition otherwise it may seriously affect the quality of the ride altogether. Not keeping them in good condition will be a major factor for the fast degradation of the suspension system which includes tires as well. We all know the importance of keeping tires in good condition.
What service ride control means?
Ride control is nothing but another name for the suspension control system. The control module which it uses is situated behind the right-side rear trim panel along with steering position.
Height sensors coupled with struts and shocks use the air pressure in such a way that the system keeps the vehicle at a proper height. Normally, the problem arises at the sensor point or the control solenoids. To properly find out the error there will be a scanner that can communicate with a control module. It also helps in testing the compressors and the solenoids without removing the components but other problems may also arise and you may not have the means to repair your truck at that point in time.
How to turn off the service ride control system?
- Get a pair of recommended resistors. The spec may range from 1.5 to 3 ohms.
- First, we have to remove the compressor cover which is located behind the rear shock.
- Now that you have completed the above step, you have to find the wiring which is located above the air compressor.
- There will be wires which are will be leading from the solenoid exhaust valve. The solenoid exhaust valve is situated above the air compressor. Find it out. Locate the blue and white wires and cut them off.
- Wire the resistor onto the two mentioned wires above.
- Get a wire stripper to twist and strip the ends of the wires.
- Make a secure connection with the ends of the wires to the resistor. To make sure you have a secure connection tuck them.
- Use electrical tape to secure the connection you have just made with the blue and white wire along with the resistor.
- Re-attach the cover around the air compressor.
If you follow the steps above, you will have successfully overridden the service control light.
Symptoms and basic tips to get it repaired
One of the tire wear problems which can be discussed is the problem of cupping. Cupping is nothing but heavy wear in small areas of the tire which says that there is a problem with the suspension. Cupping only occurs because of tires bouncing when rolling along the road. This problem clearly indicates that there is damage to the shocks or struts.
Incorrect wheel alignment might also be a cause for tire wear. This might happen due to worn-out or loosened components in a suspension system. Tire wear can be a huge indicator in diagnosing problems with the suspension. It might be a defective one or it might also be incorrectly aligned.
When a vehicle can?t maintain its original height, that is, it sags, it clearly indicates there is a problem with the springs which are an integral part of the system. The springs are no longer able to maintain the weight of the car and keep it in the height it was precisely designed to be. The front-end alignment might also be affected by this.
Replacing the shocks is the best remedy for you to keep your ride control system in a good condition which in-turn ensures a comfortable ride. Replacing the shocks will enhance the control and stability of the steering. As we had discussed earlier, the degeneration of tires is accelerated by a faulty ride control system, hence, replacing the shocks will ensure that the degradation is capped at a normal rate which finally does nothing but improving ride quality.
You might also hear the compressor activate when you start the vehicle or apply some load to it. In a lot of cases, there is a non-operative level ride due to a fault in the compressor. It might also be due to a fault in the circuit of the compressor. This is also caused by a fault in the rear shocks or the solenoids. You can also check for pressure in the bladders to detect the problems if the scanner does not provide you with a complete diagnosis.
Overriding the system might not be the toughest of tasks. As you can see, following some simple steps can help you solve the problem which you have been dealing with.
But there are permanent remedies mentioned in the article too. It might not be possible for you to repair the faults in your ride control but the next time you take your vehicle to a dealership, it is your job to make sure to check out for all faults replace the faulty parts. This will no doubt increase the longevity and comfort of your vehicle.